Mobula6 2024 V3 (2025 Edition)

The V3 of the Mobula6 2024 is Happymodel's 65mm analog BNF for the 2025-2026 season, with lots of significant upgrades to the already-winning design. The ultralight frame and the pigtail are the same, but almost every other component has been upgraded in some way.

First and foremost the flight controller has been upgraded to the CrazyG473 5in1, with significantly more processing power. The camera has been upgraded to the Nano5 Camera, which has a wider FOV (155°) and higher resolution at 1200TVL. The motors are the same 702 28,000kV, but are now thankfully direct-soldered to the FC. Although it comes with the same Gemfan 1208-3 props, this package now also includes ultralight props from HQ PROP, which is an upgrade I personally always go for. 

Here's what HappyModel has to say about it:

• Come with New CrazyG473 AIO flight controller
• Happymodel New 1200TVL Nano5 camera
• Super light 1S 65mm Brushless whoop only 17.6g
• Equipment with the lightest brushless motors-SE0702 only 1.46gram
• Smooth and powerful
• Built-in Serial ELRS receiver
• Built-in Power max to 400mw openVTX

• Brand Name: Happymodel
• Item Name: Mobula6 2024 V3 1S 65mm ultra light micro FPV Whoop 
• Wheelbase: 65mm
• Size: 81mm*81mm*37mm
• Weight: 17.6g
  

• Mobula6 2024 1S 65mm whoop Drone Frame +Canopy 
• CrazybeeG473 AIO 5-IN-1 Flight controller 
• 4x SE0702 KV28000 brushless motor 
• Gemfan 1208-3 31mm tri-blade propellers(4cw+4ccw)
• HQPROP ultralight whoop prop 1.2x1.1x3(2cw+2ccw)
• Nano5 1200TVL camera NTSC 4:3 
• Onboard 5.8G 25mw~400mw VTX 
• Spare canopy 
• Propeller disassemble tool 
• Screw driver 

• SE0702 KV28000 no plug version
• Configu-ration:9N12P
• Stator Diamter:7mm
• Stator Length:2mm
• Shaft Diameter:Φ1mm
• Motor Dimension(Dia.*Len):Φ9.5mm*14mm
• Weight(g):1.46g
• No.of Cells(Lipo):1S only

• Materials: PC
• Inch: 31mm   
• Pitch: 0.8 in 
• Weight: 0.21g    
• Mount hole diameter:  1mm

• MCU: STM32G473CEU6
• Gyro: ICM42688P
• Blackbox memory: 16MB
• Sensor: Voltage & Current
• BEC: 5V, Max. 2A
• UART: UART 1, UART 2, UART 3 (For RX), UART 4(For VTX)
• BetaFlight OSD: AT7456E
• ESC: 5A continuous
• RX: Serial ELRS 2.4GHz
• RX antenna: Enameled copper wire 31mm length
• Receiver firmware target: HappyModel EP1/EP2 2.4GHz RX 
• OPENVTX: 5.8GHz 48 channels, Max. 400mW
• FC firmware target: CRAZYBEEG473 
• USB port: SH1.0-4Pin
• Battery connector: A30
• Mounting hole size: 25.5mm x 25.5mm
• Weight: 3.83g without pigtail and vtx antenna

• Power supply: 1S LiPo/LiPo HV 
• Current: 5A continuous peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: Bluejay v0.21
• Firmware target: A_X_5_96KHz
• Default protocol: DSHOT300 DSHOT600
• Recommend ESC Startup power value to min1100/max1200

• Packet Rate option: 50Hz/150Hz/250Hz/500Hz
• ExpressLRS Firmware version: V3.0
• RF Frequency: 2.4GHz
• Antenna : Enameled copper wire antenna
• Telemetry output Power: <12dBm
• Receiver protocol: Serial_based CRSF
• Compatible with ExpressLRS V3.x.x TX Module
• Could flash single ELRS receiver firmware by Wifi
• ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx

• OPENVTX Firmware
• Support firmware upgrade by openvtx configurator
• Output power: PIT/10/25/100/400
• Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz
• Channel SEL: SmartAudio2.1
• Modulation type: FM
• Operating temperature: -10℃~+80℃
• Antenna port: IPEX1/U.FL

• Image Sensor: 1/3" CMOS
• Horizontal Resolution: 1200 TVL
• Lens: 2.1mm (M10) 155° FOV
• TV System: NTSC
• Signal-to-Noise Ratio: >52dB
• Electronic Shutter: Auto
• Automatic Gain Control (AGC): Auto
• Minimum Illumination: 0.001Lux@1.2F
• Digital Wide Dynamic Range: Auto
• Power Supply: DC 3-5.5V
• Current: 110mA@5V 120mA@3.3V
• House Material: ABS
• Net Weight: 1.57g (1.0mm plug version)